17 KLUGE

For narrow margin work.
Use on feeder or delivery.

18 KLUGE

Same as #17. Rubber disc #19K added for cardboard.

19 FLAT RUBBER SUCTION DISCS

Over 75 different sizes available up to 2" (OD) in 5 different thicknesses. Submit sample. Thicknesses of rubber available:

.020 - White - 1/2 mm
.032 - Pink - 1/32"
.040 - Tan - 1 mm
.062 - Beige - 1/16"
.080 - Green - 2 mm
Polyurethane (.032") also available.

19K-Kluge and Rudow Telescoping Suckers.
19 AB-DICK, 19HA - Hawes.
19H - Heidelberg Platen
19RZ - Royal Zenith.

Also for ATF, Bobst, Chief, Commander, Hamada, Heidelberg, KBA, Kluge, Komori, Man Roland, Miehle, Miller, Muller Martini, Multilith, Royal Zenith, Shinohara-Fuji, Speiss , and many others.

20 MIEHLE VERTICAL WASHERS

A - Feedboard
B - Gripper bar
C - Gripper head (thin)

21 SANDPAPER DISCS

A - Ready glued, 3/4"
A Large - Ready glued, 1 1/8"

B - Without glue, 3/4"
B Large- Without glue, 1 1/8"

Kluge, C&P, others.

26 KLUGE METAL CAP

Holds standard rubber sucker. For feeder and delivery.

5/8 - 18 thread.

27A - BRASS SUCKER

Offset presses, for paper.

27B - BRASS SUCKER

Offset presses, for cardboard. Add a #4, 7, 8, 14 or 15 rubber sucker.

28 MIEHLE FEEDER CAP

Plastic. Shuts off openings on feeder bar.

29A - MIEHLE VERTICAL

Fluffer wires for paper.

29B - MIEHLE VERTICAL

Fluffer wires for cardboard

29C - THUMB SCREW

For fluffer wires. Includes washer.

301 PAPER STOP DEFLECTOR

Clear rigid plastic. Equivalent to Chief M-1-184.

302 CHIEF WRENCH

Open end. Equivalent to Chief special wrench. W2155x22.

305 HOLLOW DRILL BITS

William B Rudow, Inc Hollow Drills are manufactured with a special alloy of the finest steels: chromium, vanadium, and molybdenum.  They resist wear, stay sharp longer and won’t clog, chip or twist.  The razor sharp cutting edges are carefully machined to precise tolerances.  Every Rudow Hollow Drill is thoroughly inspected before it leaves our factory.

OUR PAPER DRILLS ARE GUARANTEED AGAINST BREAKAGE – HOWEVER, NOT AGAINST FAULTY USE.

Click the PDF below to view our full range of sizes and styles available!

30A - MIEHLE VERTICAL

Air release valve. Used on feeder arm instead of #28 cap. Release a little air by turning screw. Excellent for cardboard and tissue.

30B - MIEHLE VERTICAL

Cylinder Gripper. Complete only. Fits all Verticals.

32 JOB PRESS GRIPPER FINGERS

Available in short, long and extra long. Also, available in standard & narrow widths.

Short are 1.5" long

Long are 2.5" long

Extra Long are 3.5" long

33A - KLUGE SHEET TONGUES

Sizes 1-6

LENGTHS

Size 1 - 4.5"                    Size 4 - 3"

   Size 2 - 4"                       Size 5 - 2.5"

Size 3 - 3.5"                    Size 6 - 2"

33B - SHEET TONGUE SCREW

Fits all Kluges. Includes washer.

34 MIEHLE VERTICAL TRANSFER TABLE LEVER KEY

Keeps feedboard in place. Fits all models

35 MIEHLE VERTICAL BACKSTOPS

Fits all plain boards. Simple instructions.

36 KLUGE REGISTER ROD CAM

Left or right

38A ENDLESS BELTS

ENDLESS BELTS for Miehle & Kluge. Leather for Drive.
CONVEYOR TABLE BELTS for Multilith 1250 & 1250W fabric.

39 TELESCOPING SUCKER

For ATF Chiefs, except Super Chief & Chief 15. Used with flat disc 19K.

40 FEED SUCKER BLOCK

For Chief 20, 22, 29 Presses. Convenient thumb screw for adjustment. Holds Part 39.

41A PIN WRENCH

Straight type. Small and large.

Small is 5 1/4" long, 1/8" x 3/16" ends

Large is 9 3/4" long, 5/16" on both ends

 41B PIN WRENCH

"S" type. Small

5 1/4" long, 1/8" x 3/16" ends

43 KLUGE REGISTER ROD HOLDER

44 KLUGE WRENCH, NUTS AND BOLTS

Includes all popular nuts and bolts.

B - Wrench.
C - Gripper nut.
E - Delivery pickup bolt.
F - Delivery track bolt.

45 KLUGE MISCELLANEOUS PARTS

Fits all models.

A - Side guide tongue. Left and right.
B - Magazine separator spring.
C - Center comber spring.
D - Side guide eyebolt holds side guide to platen.

46 BOOK TRIMMING GUIDES

Challenge style. Bolt portion fits on back finger gauge of cutter. Keeps any size booklets flat for trimming.

47 BOOK TRIMMING GUIDES

Economy style. Fits on back gauge of cutter.

48 KLUGE

A - Delivery pickup bolt.
B - Delivery pickup clamp top.
C - Delivery pickup clamp base. Specify left or right.
D - Delivery pickup suction tube.

51 KLUGE

A - Kluge side guide, complete. Left or right. Regular (6"stem) or Long (8" Stem)

B - Kluge side guide block. Regular (7/8" long x 1/2" wide x 1/8" thick) or thick (7/8" long x 1/2" wide x 1/4" thick).

C - Bottom feed gauge block.  Regular (7/8" long x 1/2" wide x 1/8" thick), thick (7/8" long x 1/2" wide x 1/4" thick), narrow (1/2" long x 1/2" wide x 1/8" thick) or narrow-thick (1/2" long x 1/2" wide x 1/4" thick).

D - Feed gauge tongues only.

E - Kluge side guide, complete with offset stem. Left or right.

52 KLUGE

A- Kluge Bottom Gauge Band. Specify length - 19-1/2", 23-1/4" or 25-1/2"
B- Kluge Bottom Gauge Band Clamp. Quick release.
C- Kluge Bottom Gauge Band Clamp with screw to hold band. Specify left or right.

53 BLOWER FLEXIBLE STEEL TUBING,

Fits all Kluges. 5' length.

54 KLUGE FEEDING SUCTION TUBES

A - Cardboard , left KG-571
B - Cardboard, right KG-571A
C - Paper, left KG-577
D - Paper, right KG-577A
E - Dummy KG-580

65 CHIEF SHEET SEPARATORS

(Cat Whiskers). For small offset presses.

Chief 15-17.

Available in Bronze.

65 DAVIDSON SHEET SEPARATORS

(Cat Whiskers). For small offset presses.

Available in Brass.

65 HAMADA SHEET SEPARATORS

(Cat Whiskers). For small offset presses.

Available in Brass (standard) and Bronze.

65 KOMORI SHEET SEPARATORS

(Cat Whiskers). For small offset presses.

Available in regular = 0.13mm thick.

Fits  Komori or Shinohara/Fuji and others.

65 MULTI SHEET SEPARATORS

(Cat Whiskers). For small offset presses.

Available in Brass (standard) and Bronze.

65 RYOBI SHEET SEPARATORS

(Cat Whiskers). For small offset presses.

Available in Bronze.

69 GRIPPER BOLTS

For Kluge or C & P

Sold in pairs.

70 RYOBI / ITEK

Telescoping sucker. Comes with #19K discs.

73 A.B. DICK

Metal telescoping sucker. Comes with #19K discs. For difficult and wavy stock.

73P A.B. DICK

Plastic telescoping sucker with shut-off valve. Comes with a #66 sucker.

74 A&B SET

Telescoping suckers. Uses #19K discs. For difficult and wavy stock.

74C NEW STYLE MULTILITH

Telescoping sucker. 1250-1250W and 1850. Comes with #19K discs.

75 CHIEF 15 & 17

Telescoping sucker. Uses #19K or 19-AB DICK discs. For difficult and wavy stock.

JOB PRESS GRIPPERS

For C&P, Kluge, and other job presses taking similar grippers. Rudow Job Press Grippers replace the grippers on your job press. Job Press Gripper Fingers (#32) snap on tightly, holding sheets rigid, preventing slurs. One set consists of a left and right gripper and 3 pairs #32 gripper fingers.
In sizes 8 x 12; 10 x 15; 12 x 18.